BST Urethane represents a breakthrough technology that offers exceptional physical and chemical properties for a urethane. BST is a one-part, trowel-applied, tacking moisture-cure urethane with unsurpassed green strength and ridge-holding capabilities. It trowels easily and, once cured, is not affected by moisture or water.
Hardwood Products
Urethane Adhesives
, 
EFA+ (Elastomeric Flooring Adhesive)
Bostik's EFA+ Elastomeric Flooring Urethane Adhesive and Moisture Vapor Retarder is a one-part, trowel-applied, moisture-cure urethane adhesive that does NOT contain water. Once cured, EFA is waterproof and is not adversely affected by exposure to moisture or water. EFA's elastomeric characteristics allow the adhesive to move with the wood as it expands and contracts over the life of the floor.
Resources
, 
Bostik's BEST
BEST is a one-part, trowel-applied, tacking moisture-cure urethane adhesive. This advanced, scientifically-formulated adhesive does NOT contain water. Once cured, Bostik's Best is waterproof and is not adversely affected by exposure to moisture or water; its superior properties provide a tough, flexible, tenacious bond to a variety of surfaces. Bostik's Best's elastomeric characteristics allow the adhesive to move with the wood as it expands and contracts over the life of the floor.
Resources
, 
, 
TKO Urethane (New and Improved) 0 VOC, 0 Solvent
Bostik's TKO is a one-part, trowel-applied, moisture-cure urethane; this advanced, scientifically-formulated adhesive does NOT contain water. Once cured, TKO is waterproof and is not adversely affected by exposure to moisture or water; its superior properties provide a tough, flexible, tenacious bond to a variety of surfaces. TKO's elastomeric characteristics allow the adhesive to move with the wood as it expands and contracts over the life of the floor.
A technical innovation in moisture-cure urethane adhesives that offers the following:
- Easy to spread
- Holds a better ridge
- Cleans up faster when wet than most urethane adhesives
- Contains Bostik's Blockade™ Antimicrobial Protection
- 0-Solvent
- 0-VOC (as calculated per SCAQMD 1168)
Resources
, 
, 
Moisture Vapor Barrier Coatings
D-250 Moisture Vapor Barrier Coating
D-250™ Moisture Vapor Barrier Coating is a two-component, water-based, penetrating epoxy formulated to incorporate antimicrobial protection and dramatically reduce moisture vapor transmission from substrates including “freshly poured green concrete”, properly-prepared concrete, cement backer board, cement patch/underlayments, radiant heat flooring, and cement-based terrazzo prior to the installation of carpet, vinyl/VCT, engineered or solid hardwood, porcelain, marble, granite, or ceramic tile floor covering.
Resources
, 
, 
, 
Surface Preparation
Universal Primer
Resources
, 
Bostik UltraFinish™ Portland Cement-Based Patch
Bostik UltraFinish™ is a fast-setting, latex-fortified, Portland cement-based patch for interior use prior to the installation of hardwood, ceramic, carpet, vinyl, or rubber flooring. This product may be used to skim coat or feather-edge up to 1" deep in one application. Floor covering can be installed typically in as little as 15-20 minutes over concrete, wood, ceramic and quarry tile without the requirement of priming or the use of a liquid additive. When mixed with Durabond D-L16™ High Strength Additive or Bostik's Hydroment 425 Multi-Purpose Acrylic Latex Admixture instead of water, Bostik UltraFinish can be used as an embossing leveler.
This product contains Bostik's Blockade™ Antimicrobial Protection, which inhibits the growth of bacteria, mold, or mildew on the surface of the dried cement; the dried cement resists stains caused by mold.
MSDS (http://msds.bostik-us.com)
Resources
Fast Patch 102
Fast Patch 102 is a fast-setting, polymer-modified, cement-based compound. Simply mix with water to repair cracks, holes and uneven surfaces from feather-edge up to 1/2" thick in a single application. Use Fast Patch 102 prior to installation of carpet, wood, ceramic tile and stone floors. It can be applied over concrete, existing ceramic tile, exterior-grade plywood and well-bonded vinyl tile.
Resources
, 
D-261 Extreme Moisture Vapor Barrier Coating
D-261™ Extreme Moisture Vapor Barrier Coating is a two-component, high performance, rapid drying, epoxy formulated to dramatically reduce moisture vapor transmission and surface alkalinity from substrates including; “freshly-poured/green concrete”, properly prepared concrete, cement backer board, cement patch/underlayments, radiant heat flooring, and cement-based terrazzo prior to the installation of carpet; vinyl/VCT; engineered or solid hardwood; porcelain, marble, granite, or ceramic tile floor covering. D-261 contains Bostik’s Blockade™ antimicrobial protection and utilizes a breakthrough, silver-based, antimicrobial agent that provides built in protection to inhibit the growth of a broad range of odor causing bacteria, mold and mildew on the surface of the coating’s film. D-261 is uniquely formulated so that it may be applied to fresh “green” concrete as soon as it has achieved “initial set” (when the concrete can be walked on without disturbing the surface). It is pigmented light green for visual indication of coverage and film thickness during the installation process. It is extremely durable and wear resistant.
When properly installed, D-261 is designed to reduce the moisture vapor emission rate of even the most challenging concrete slabs from < 25 pounds per 1,000 ft2 per 24 hours to < 3 lbs. per 1,000 ft2 per 24 hours (per ASTM 1869). This non-flammable, non corrosive, low odor, non-blushing formulation requires no solvent wiping, and has no application window in which floor covering adhesives must be applied to achieve a strong bond. D-261 is formulated to be effective in reducing the surface alkalinity of concrete slabs to pH levels of 9 or lower as recommended by the Carpet and Rug Institute and the Canadian Carpet Institute, making them ideal for bonding with most adhesives.
Resources
, 
, 
, 
Cleaner
Ultimate Adhesive Remover
Use Bostik's Ultimate Adhesive Remover to remove wet and cured urethane adhesive from the surface of pre-finished (non-wax) wood flooring. Ultimate Adhesive Remover is a readily-biodegradeable, low-odor, water-rinseable solution.
Bostik's Ultimate Adhesive Remover is available in two formulations: liquid and pre-soaked, ready-to-use towels.
Resources
BladeCote Blade and Bit Lubricant
Regular use of BladeCote™ Blade and Bit Lubricant on saw blades, router and drill bits and knives significantly reduces cutting friction and the buildup of resin or pitch. BladeCote dries in seconds and will not gum-up, even after several applications.
- Prevents resin buildup. Reduces blade cleanings.
- Extends overall life of blades and bits
- Contains NO silicone or petroleum oil.
- Will NOT stain wood or interfere with glues or finishes.
- Reduces cutting friction and heat.
- Prolongs equipment life by reducing saw or drill motor drag.
- Increases productivity by less downtime for saw blade changeovers.
- Works equally well on steel or carbide, stellite and diamond-tipped cutting blades.
Extends blade & bit life:
- Will not build-up even after several applications
- Will not stain or effect finishing of wood
- Contains no petroleum oils or silicone
Other Applications:
- Chisels
- Shaper Cutters
- Router Bits
- Planer Blades
- Superb, long lasting, penetrating lubricant for numerous industrial, commercial and household uses.
MSDS (http://msds.bostik-us.com)
Resources
GlideCote Table & Tool Surface Sealant
Regular maintenance of saw tables and receiving tables with GlideCote™ Table and Tool Surface Sealant significantly reduces sliding friction on all metal, laminate, and plastic surfaces. Perfect for table saw beds, drill presses, lathes, planers, band saws, miters, panel saws, and all hand tools.
- Eliminates “hang-ups” on sliding surfaces.
- Protects all tools and equipment from rust.
- Up to 30% slicker than paste wax.
- Easier and quicker to apply than paste wax.
- Lasts three times (3x) longer than paste wax.
Additional Benefits:
- Reduces sliding friction and hang-ups
- Will not build-up even after several applications
- Will not stain or effect finishing of wood
- Contains no petroleum oils or silicone
MSDS (http://msds.bostik-us.com)
Resources
Moisture Vapor Protection
Vapor-Lock™ Wood Flooring Urethane Adhesive/Vapor-Retarding Membrane
Vapor-Lock™ is a new and improved one-part, trowel-applied, rapid tacking, very low permeability moisture-cure urethane adhesive and vapor retarding membrane. This scientifically formulated adhesive/membrane does NOT contain water, is virtually odorless, and has 0%-VOC's.
Vapor-Lock offers a tenacious waterproof bond to a variety or substrates and is not adversely affected by exposure to moisture, water, or alkalinity; it can also create a vapor-retarding membrane designed to reduce moderate amounts of moisture vapor transmission from the subfloor and bridge cracks that can occur in the substrate prior to or after installation (up to 1/8”).
MSDS (http://msds.bostik-us.com)
Resources
, 
, 
MVP4 (Moisture Vapor Protection)
Bostik's MVP4™ is a one-part, trowel-applied, elastomeric, moisture-cure urethane membrane designed to:
1. Reduce Moisture Vapor Transmission from the subfloor
2. Create a Noise Reduction Barrier over the substrate, Peace Noise Reduction
3. Establish an anti-fracture membrane that can bridge subfloor cracks up to 1/8" prior to or after installation
MVP4 contains Bostik® Blockade™ Antimicrobial Protection, which inhibits the growth of bacteria, mold, or mildew on the surface of the dried cement; the dried cement resists stains caused by mold.
MSDS (http://msds.bostik-us.com)
Resources
, 
, 
, 
Bostik Ultra-Set SingleStep
Bostik's Ultra-Set® SingleStep™ is a one-part, trowel-applied, tacking moisture-cure urethane adhesive & moisture vapor protection membrane. This scientifically-formulated adhesive and membrane is very tenacious, has very low moisture permeability, and is formulated with patent-pending
Thickness-Control™ Spacer Technology to insure proper membrane thickness between hardwood flooring and the substrate. Bostik's Ultra-Set SingleStep contains NO WATER, is 0-VOC and contains 1% recycled materials.
Resources
, 
, 
Repair Kits
Simple-Fix™ Hardwood Flooring Epoxy Repair Kit
Simple-Fix™ is a versatile, low viscosity, two-component, epoxy adhesive used to repair hollow spots, replace floor boards and to install thresholds, moldings and medallions.
This adhesive is designed for use with engineered wood, parquet, solid wood and bamboo flooring designed and recommended in writing by the flooring manufacturer for glue-down applications.
Simple-Fix has extremely high bond strength, making it the perfect solution for bonding wood to wood, or wood to concrete. Simple-Fix is specifically formulated to be a simple repair solution that is easily dispensed with an off-the-shelf caulking gun.
Benefits:
• Fits in an off the shelf caulking gun
• Versatile formulation works with engineered wood, parquet, solid wood and bamboo flooring
• Exceptional bond to wood and concrete
• Low odor, 0% VOC, user-friendly formulation
• Does not contain water
Resources
